AGA TCDCNGMBRG Installation Guide

06/15 EINS 517026TC/DC INTEGRATED MODULE (FFD)(with Gas Top Burners)For use in USA/CanadaInstallationGuidePLEASE READ THESE INSTRUCTIONS BEFORE COMMEN

CAUTION: THIS INSTALLATION MUST CONFORM WITH LOCAL CODES OR, IN THE ABSENCE OF LOCAL CODESWITH THE NATIONAL FUEL GAS CODE ANSI.Z223.I AND NATIONAL ELE

The range is installed adjacent to the LH side of an AGA Total Control/AGA Dual Control.Installation of the Module must, therefore be in conjunction w

5. The Module plinth can now be levelled and fitted up to the main appliance. Position the Module plinth alongside the AGA TC3/DC3 leaving no gap betw

Fig. 6A DESN 516276MODULE PLINTHBASE3/8” (11mm)HEIGHT DIFFERENTIALHOTCUPBOARDPLINTH BASE11/64” (4.5 mm)GAPFOR AGA TC5/DC5 + MODULE ONLY6. Attach Mo

Fig. 7A DESN 516858FOR AGA TC5/DC5 + MODULE ONLY7. Prior to electrical connections, remove top plate assembly from Module as follows:- a) Rem

158. Check current is OFF.Connect mains wire to terminal block at the rear of the cooker (See Fig. 9). Sufficient cable should be available to allo

11. Assemble a U.L.-listed strain relief in the opening.12. Insert the power supply cord through the strain relief, allowing enough slack to easily at

Fig. 10 DESN 51704415. Apply tape (provided) to the rear of the lap strip on the Module front plate.16. Slide Module onto plinth until rear tongue b

Fig. 11ADESN 517034AGA DC3G (Power Flue) Gas Supply Connections(Approximate Positions)Fig. 11 DESN 517042Gas Supply ConnectionsMODULE GAS SUPPLY CONNE

Fig. 12 DESN 517045GAS ADJUSTMENT FORNATURAL GAS/PROPANEPressure TestingThe maximum gas inlet pressure to the appliance must not exceed 12” wg for N.G

ContentsProduct Safety 3General Notes 4Health and Safety 4General Installation Requirements 4Location 5Specification - AGA Total Control (TC3) / Dual

17. Replace Module top plate as follows:a) Support top plate at front and reconnect the wiring to the two neons.b) Carefully lower the top plate into

21. Once the handrail assembly is located squarely, lock the handrail in position by tightening the grub screws on the underside of each handrail brac

DISCONNECT FROM ELECTRICITY SUPPLY BEFORE SERVICING.WHEN RE-WIRING ANY ELECTRICAL COMPONENTS REFER TO CIRCUIT DIAGRAM AND ELECTRICAL SCHEMATICDIAGRAM

D. TO CHANGE IGNITION ELECTRODE1. Turn off electricity supply.2. Remove top plate and hotplate, (See sections A and B).3. Disconnect the electrode cab

Fig. 15 DESN 511617BURNER CAP RETAINING LUGSFig. 15A DESN 513513DESN 513898Fig. 15B24

Fig. 16 DESN 517047SPARKGENERATORTERMINALBLOCK25Access to the gas governor is as follows:-a) Remove pan supports and all control knobs.b) Remove four

Fig. 17Fig. 18DESN 511649DESN 51165026

Fig. 19Fig. 20DESN 511651DESN 511652GAS RAILSUPPORT BRACKETSCREWSGAS RAILSUPPORT BRACKETSCREWSGAS TAPTUBE NUTGAS RAILTUBE NUT27

CAUTION: LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS WIRING ERRORS CANCAUSE IMPROPER AND DANGEROUS OPERATION.VERIFY PROPER OPERATIO

AGA TC/DC INTEGRATED MODULE (GAS HOB)CIRCUIT DIAGRAM29

PRODUCT SAFETYMEANING/DESCRIPTION SIGNIFICATION/DESCRIPTIONSYMBOLWARNING/CAUTIONAn appropriate safety instructionshould be followed or caution to apot

30l In the event of your appliance requiring maintenance please call AGA Service or contact your authorised distributor/stockist.l Your cooker must on

31

www.agamarvel.comSupplied byAGA Marvel1260 E. Van Deinse St.Greenville, MI 48838Business (616) 754-5601Fax (616) 754-9690Toll Free Telephone 8

HEALTH AND SAFETYConsumer ProtectionAs responsible manufacturers we take care to make sure that our products are designed and constructed to meet the

REFER TO FIG 1 & 2The side wall clearance above the hob shall be greater than 3”.Surfaces over the top of the range must not be closer than 30” an

SPECIFICATION - AGA TOTAL CONTROL (TC3) / DUAL CONTROL (DC3) WITHTC/DC MODULE (GAS HOB) (TC3M/DC3M)The extension channel section at the rear of each s

SPECIFICATION - AGA TOTAL CONTROL (TC5) / DUAL CONTROL (DC5) WITHTC/DC MODULE (GAS HOB) (TC5M/DC5M)Fig. 2 DESN 517033COOKER DIMENSIONSWhen surveying f

INSTALLATION CLEARANCES OF COMBUSTBLE CABINETS ADJACENT TORANGE AGA TOTAL/ DUAL CONTROL (WITH MODULE SHOWN)Installation Clearance of Combustible Cabin

HOTPLATENATURAL GASR.H.F. L.H.R. R.H.R. L.H.F.BURNER TYPE ULTRA RAPID RAPID SEMI-RAPID SEMI-RAPID(WOK)MAXIMUM HEAT 3.5 kW 3.1 kW 1.8 kW 1.8 kWINPUT 12